File Name: readme.txt IBM xSeries 330 Diagnostics Flash Update Diskette readme.txt Version 1.01 System 8675 CONTENTS --------- 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Configuration Information 5.0 Unattended Mode 6.0 Web Sites and Support Phone Number 7.0 Trademarks and Notices 8.0 Disclaimer 1.0 Overview -------------- 1.1 Overview about this code This README file contains the latest information about installing the IBM xSeries 330 Diagnostics. 1.2 Limitations N/A 1.3 Enhancements N/A 1.4 Level of Recommendations and Prerequisites for the Update N/A 1.5 Dependencies N/A 2.0 Change History -------------------- 2.1 IBM xSeries 330 Diagnostics Flash Update Diskettes 1.00 to 1.01 - added a MMX subtest to the CPU/Coprocessor test - fixed a problem where the CPU/Coprocessor test would hang with a ServeRAID card installed 2.2 IBM xSeries 330 Diagnostics Flash Update Diskettes 1.00 - Initial Release 3.0 Installation and Setup Instructions *Note: If installing from an update package, see additional instructions, in Appendix A. ----------------------------------------- 3.1 Step by step instructions for this code update - Insert the "IBM xSeries 330 POST/BIOS Flash Disk" into drive A. - Start up or restart your IBM xSeries 330 server. - The system will boot from the diskette and present a window which allows you various options. Choose "2 - Update Diagnostic". - The system will prompt you to insert the diskette containing diagnostics file $TVydiag.us1. Insert the "IBM xSeries 330 Diagnostics Flash Update Diakette" into drive A and hit enter. - After the images are loaded from diskette the system will ask you to wait while the images are flashed into ROM. When this is complete you will be prompted to remove the diskette and hit enter to restart the system. 3.2 Other N/A 4.0 Configuration Information ------------------------------- N/A 5.0 Unattended Mode --------------------- 5.1 Steps for unattended mode - Boot to DOS - Copy flash2.exe from the "IBM xSeries 330 POST/BIOS Flash Disk" and all *.us* files from the "IBM xSeries 330 Diagnostics Flash Update Diskette" to the same directory on some media capable of storing 1.44MB of data - From the directory just copied to, run "flash2.exe /u /d" 6.0 WEB Sites and Support Phone Number ---------------------------------------- 6.1 IBM Support Web Site: http://www.pc.ibm.com/support 6.2 IBM Marketing e(logo)server xSeries Web Site: http://www.ibm.com/eserver/xseries 6.3 If you have any questions about this update, or problems applying the update go to the following Help Center World Telephone Numbers URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 6.4 Intellistation web site http:www.pc.ibm.com/intellistation 7.0 Trademarks and Notices ---------------------------- N/A 8.0 Disclaimer ---------------- 8.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 8.2 Note to Government Users Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation. Appendix A: Package Specific Installation Instruction This update is packaged as a self-extracting PackageForTheWeb (PFTW) executable file. To unpack, this update requires that your TEMP environment variable be set to a path with read/write access. You must be logged in as an administrator. The package update log, ux.log, is created on the system drive. To locate the log file go to: %SystemDrive%\uxlog\ux.log The command-line syntax for PackageForTheWeb firmware update package is: Package.exe [-s] [-a [-s] | [-r] | [-c] | [-x directory] | [-xd] | [-w] | [-?] ] [-s] This command installs the Package-For-The-Web software silently and does not prompt if files are to be over-written in the %temp% directory. [-a] This command passes all subsequent commands to the PFTW software to install the update package. [-s] This command runs a silent and unattended update. For firmware updates, the update is scheduled to run on the next reboot. An immediate reboot can be forced with the -r option. [-r] This command schedules the update and reboot immediately. It can be used with or without the -s command. [-c] This command cancels any scheduled firmware update and records results of this operation in the log file. Only one firmware package can be scheduled at a time, if a firmware update needs to be applied instead of the currently scheduled firmware update package, cancel the current (run with the -c option on any firmware package) package. Then, run the applicable firmware package. [-x directory] This command is used with firmware updates to extract the update to the directory named directory. The PackageForTheWeb executable extracts itself to a subdirectory in the %TEMP% directory, a relative directory will be relative to that location. You must specify an absolute directory if you do not want to use the default directory. [-xd] This command is used with firmware updates to extract to a floppy diskette. The floppy diskette can then be used to boot from and apply the update. This option is not available for all firmware updates, such as tape drive and hard-disk drive updates. [-w] PowerQuest Virtual Boot Environment requires that there are 2 free sectors on the first track before it can schedule a firmware update. Use this option only if scheduling an update failed because 2 free sectors were not available on the first track. This option clears the non-boot and the non-partition information sectors on the first track. Typically, these sectors are not used. Before clearing the sectors a copy of the complete first track is saved in the %temp% directory from which the update runs. [-?] This command displays information about the command line switches. The command line switches -s, -r -c and -e are unnattended. Other command line options such as display help (-?) might require that you hit any key to continue. If Windows packages are run without any command line options, a GUI is displayed. This GUI offers all of the options that are available using the command line.