**************************************************************** | | | IBM eserver BladeCenter | | Integrated System Management Processor Update | | | | System: JS20 model 8842 | | Build ID: BQ8T22A | | Version: 1.02 | | | | (C) Copyright International Business Machines Corporation | | 2004. All rights reserved. | | | | US Government Users Restricted Rights -- Use, duplication | | or disclosure restricted by GSA ADP Schedule Contract with | | IBM Corp. | | | | Note: Before using this information and the product it | | supports, read the general information under "NOTICES AND | | TRADEMARKS" in this document. | | | | Updated: 1 August 2005 | **************************************************************** CONTENTS 1.0 About this ReadMe file 2.0 Change history 3.0 Installation and Setup Instructions 4.0 Configuration Information 5.0 Unattended Mode 6.0 Web sites and phone support 6.1 Web sites 6.2 Software service and support 6.3 Hardware service and support 7.0 Notices and Trademarks 8.0 Disclaimer 1.0 About this ReadMe file --------------------------- The BladeCenter Integrated System Management Processor firmware can only be updated through the BladeCenter Management Module web interface. It will not affect any device drivers. 1.1 Dependencies: - none 2.0 Change history ------------------- Version 1.02 - Build ID BQ8T22A - Support for 8842-4TX - New Thermal support for throttling Integrated System Management Version 1.01 - Build ID BQ8T21A fixes for the following problems - Incorrect voltage threshold on 1.6V (GA2) - INT:JS20 report voltage error when restarting MM - ELP: POSTBIOS:2B200031 at 10 C - H8 is getting corrupted during combined image update Version 1.00 - Build ID BQ8T20A - Original Release 3.0 Installation and Setup Instructions ---------------------------------------- To install the BladeCenter Integrated System Management Processor firmware from the BladeCenter Management Module web interface, perform the following steps: a). Open a Web browser. In the address or URL field, type the IP address or host name of the Management Module to which you want to connect. The Enter Network Password window opens. Note: The Management Module defaults to DHCP. If a DHCP host is unavailable, the Management Module assigns a static IP address of 192.168.70.125. b). Type your user name and password in the Enter Network Password window. If you are using the IBM Management Module for the first time, you can obtain your user name and password from your system administrator. All login attempts are documented in the event log. A welcome page opens in your browser. Note: The Management Module is set initially with a user name of USERID and password of PASSW0RD (with a zero, not an O). This user has read/write access. Change this default password during your initial configuration for enhanced security. c). Select a timeout value, in minutes, in the field provided. If your browser is inactive for that number of minutes, the Management Module logs you off the Web interface. d). Click Continue to start the session. The browser opens the System Health page, which gives you a quick view of the system status. e). In the navigation frame, click Firmware Update under Blade Tasks, select the Target blade slot number, then click Browse. f). Switch to the drive and directory containing the unpackaged files. Navigate to the PKT file you want to update, named as: BQ8Tbbr.PKT Where bb = build ID, and r = revision. g). Click Open. The file (including the full path) appears in the box beside Browse. h). To begin the update process, click Update. A progress indicator opens as the file is transferred to temporary storage. A confirmation page opens when the file transfer is completed and the BladeCenter Integrated System Management Processor has been restarted. Note: To cancel this process at any point, click Cancel. 4.0 Configuration Information ------------------------------ 4.1 Level of Recommendations and Prerequisites for proper blade operation: - Open Firmware version FW05111140 , or later. - Broadcom NIC boot code version 3.21, or later. - Broadcom ASF code version 2.30, or later. - Management Module version 73H, or later. - Ethernet Switch: - Nortel, version 20.1.2.2, or later. - DLink, version 95, or later. 5.0 Unattended Mode -------------------- This update utility does not support unattended installations but there are other ways to incorporate unattended installations of this code. Refer to section 3 for instructions on updating BladeCenter Integrated System Management Processor firmware. 6.0 WEB Sites and Phone Support -------------------------------- Information and assistance is available through the IBM Web site and by phone. 6.1 Web sites ------------- IBM Support Web Site: http://www.pc.ibm.com/support IBM eserver BladeCenter Web Site: http://www.ibm.com/eserver/bladecenter IBM IntelliStation Web site: http://www.ibm.com/pc/intellistation 6.2 Software service and support --------------------------------- Through IBM Support Line, you can get telephone assistance, for a fee, with usage, configuration, and software problems with xSeries servers, IntelliStation workstations, and appliances. For information about which products are supported by Support Line in your country or region, go to http://www.ibm.com/services/sl/products/. For more information about Support Line and other IBM services, go to http://www.ibm.com/services/, or go to http://www.ibm.com/planetwide/ for support telephone numbers. In the U.S. and Canada, call 1-800-IBM-SERV (1-800-426-7378). 6.3 Hardware service and support --------------------------------- You can receive hardware service through IBM Services or through your IBM reseller, if your reseller is authorized by IBM to provide warranty service. Go to http://www.ibm.com/planetwide/ for support telephone numbers, or in the U.S. and Canada, call 1-800-IBM-SERV (1-800-426-7378). In the U.S. and Canada, hardware service and support is available 24 hours a day, 7 days a week. In the U.K., these services are available Monday through Friday, from 9 a.m. to 6 p.m. 7.0 Notices and Trademarks --------------------------- INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you. This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. IBM, the e-business logo, eServer, and IntelliStation, are trademarks of the IBM Corporation in the United States, other countries, or both. 8.0. Disclaimer ---------------- 8.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 8.2 Note to Government Users: Documentation related to restricted rights -- Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.