LS20 POST/BIOS Flash Disk
	     		Version 1.01, , Build ID: BKE116AUS  
        	       	Installation README File
			System Supported: 8850
	      		
			[SERVICE USE RETAIN #H183797]

CONTENTS
________

       1.0   Overview
       2.0   Change History
       3.0   Installation and Setup Instructions
       4.0   Configuration Information
       5.0   Unattended Mode
       6.0   Web Sites and Support Phone Number
       7.0   Trademarks and Notices
       8.0   Disclaimer

       1.0   Overview

              1.1  This README file contains the latest information about
                   installing the LS20 POST/BIOS.

              1.2  Limitations - NA

              1.3  Enhancements - NA

              1.4  Level of Recommendations and Prerequisites for the Update:

                -  
                
              1.5  Dependencies

        2.0   Change History

              V1.01 - BKE116A - April 27, 2005
              ----------------------------------

                - Initial release


        3.0   Installation and Setup Instructions

              The procedure to update the POST/BIOS is as follows:

              3.1  Insert the "LS20 POST/BIOS Flash Disk" into drive A.

              3.2  Start up or restart your LS20 server.

              3.3  The system will boot off of the disk and present
                   a window which allows you the option to flash various
                   options.  Choose "1 - Update POST/BIOS".

              3.4  You will be asked if you would like to move the current
                   POST/BIOS image to the backup ROM location.  If you
                   select 'Y', the current code will be flashed in to the
                   backup bank immediately.

              3.5  If the current system POST/BIOS supports the Asset Tag
                   feature, you will be asked if you would like to change it.
                   If you select 'Y', you will be able to enter a new number.

              3.6  You will then be asked if you would like to save the current
                   code to a disk.  If you select 'Y', you need to have
                   a formatted disk already available, or specify a fully
                   qualified path and file name.

              3.7  At this point, the image will be loaded from the disk, and
                   you will be asked to choose which language you wish to use during
                   POST and in Setup.  If you select a choice other than English,
                   the selected language will be merged into the image.
                   There is also an option to Quit the flash update on this menu.

              3.8  After this completes the system will update the flash ROM
                   with the new code.  When this is complete you will be prompted
                   to remove the disk and hit return to reboot the system.


       4.0  Configuration Information

       5.0  Unattended Mode

             5.1   Steps for unattended mode.

                   5.1.1  Modify CONFIG.SYS on the Flash Diskette to read:
                          "SHELL=FLASH2.EXE /u /r"
                          Or use FLASH2.EXE /u /r from your script. 
                          /u is for unattended mode 
                          /r is to specify reboot after flash is done
                        ** reboot is recommended after flash.   
                   
                   5.1.2  Reboot the system with the Flash Diskette in Drive A:

                        ** Note: An optional parameter of "/a:<number>"
                           can be added to allow for storing a system
                           asset tag number where "<number>" is replaced
                           with up to a 32 digit string.

       6.0  Web Sites and Support Phone Number

              6.1  IBM Support Web Site:
                   http://www.pc.ibm.com/support

              6.2  IBM Marketing Web Site:
                   http://www.pc.ibm.com/ww/eserver/xseries/

              6.3  If you have any questions about this update, or problems
                   applying the update go to the following Help Center World
                   Telephone Numbers URL:
                   http://www.pc.ibm.com/qtechinfo/YAST-3P2QLY.html.


       7.0  Trademarks and Notices
       
              7.1 IBM and the e(logo) are registered trademarks of 
                  International Business Machines Corporation.
                  
              7.2  U.S. Government Users Restricted Rights - Use, duplication
                   or disclosure restricted by GSA ADP Schedule Contract with
                   IBM Corporation.  IBM web site pages may contain other
                   proprietary notices and copyright information which should
                   be observed.
                   
       

       8.0  Disclaimer

             THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
             KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR
             IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED
             WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
             MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS
             DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES
             TO ANY PATENTS OR COPYRIGHTS.