IBM eserver xSeries 345 Remote Supervisor Adapter II Update for Windows System 8670 Version 1.05, Build ID: GEE833A, Revision 16 CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Unattended Mode 5.0 Web Sites and support phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview ________________________ 1.1 This will update the IBM Remote Supervisor Adapter II software only. It will not affect any device drivers. 1.2 Limitations SSL is a commonly used security technology that uses encryption to provide secure TCP/IP communication. In order to comply with regulations regarding the export of products that contain cryptography, the IBM Remote Supervisor Adapter II is shipped without SSL support. In order to install SSL, the installation key file must be obtained and loaded into the Remote Supervisor Adapter II via the web interface. Once the file is loaded, SSL is installed and can be enabled or disabled as desired. If there is an error in loading the IBM Remote Supervisor Adapter II software, retry loading the software by repeating the instructions in section 3.0. 1.3 Enhancements - none 1.4. Level of Recommendations and Prerequisites for the update: - none 1.5 Dependencies: - none 2.0 Change History ________________________ IBM Remote Supervisor Adapter II Installation Version 1.05 - Corrected a problem with rebooting the ASM corrupting settings - Fixed an issue wherethe Remote control screen did not close - Fixed a problem where video was lost after cancelling remote disk image - Stopped a USB memory device from mounting as a CD ROM drive - Fixed a problem with the ASM not detecting an analog modem connected to the serial port - Removed the dialback command from the supported command list - Fixed a problem with remote graphics over a PPP connection - Fixed a problem that caused the ASM to reset when the Security link on the Web interface was clicked - Fixed a problem where the second login attempt was rejected - Intermittently the system did not redirect the local screen to console - Added new options under TCP via MIB file - Fixed a problem where the Windows blue screen capture would fail IBM Remote Supervisor Adapter II Installation Version 1.04 - Improved the recovery procedure for an ASM interconnect bus hang - Added support for Lightweight Directory Access Protocol - Added support for the Blue Identification LED - Added Remote Disk Multi Drive Support - Added Serial Console Redirection capability IBM Remote Supervisor Adapter II Installation Version 1.03 - Added support for the Belgian keyboard - Corrected a failure that occurred while flashing the Integrated Systems Management Processor - Corrected an ethernet connection problem - Fixed the save and restoration of the ISMP gateway setting IBM Remote Supervisor Adapter II Installation Version 1.02 - Corrected the remote disk feature which would not work if it was run with a Japanese user name - Fixed a condition where alerts would not be generated after the system recovered from a CPU over temperature or system over voltage condition - Added SNMP command support - Added support for French, Italian, German, Spanish and UK keyboards IBM Remote Supervisor Adapter II Installation Version 1.01 - Provided the numeric pager alerts with different codes to distinguish faults from recoveries. - Corrected the firmware to recognize recoveries from ISMP detected faults on other systems connected via the ASM interconnect. IBM Remote Supervisor Adapter II Update Version 1.00 - First release 3.0 Installing and Setup Instructions ______________________________________ This utility will update the IBM Remote Supervisor Adapter II software under the Windows Operating System . It requires the installation of the correct Remote Supervisor Adapter II for Windows device driver. To use this utility, perform the following steps: a). Copy filename.exe (where filename is the name of the file that you downloaded) to a temporary directory on the hard disk. Run filename.exe from a command line window. Several files will be extracted and placed in the directory where filename.exe is located. b). In this directory, at the command prompt, type WFLASH -r Text will scroll across the console screen while the update process is occurring. The update process could take up to ten minutes to complete. c). When the utility is finished with the update, the text will stop scrolling across the console screen and the adapter will be restarted. The successful update ends with the text "Rebooting RSA...done". d). Remove any diskette from the diskette drive and the system is ready for use again. 3.1 SSL Installation ______________________ 3.1.1 Begin a web interface session with the selected Remote Supervisor Adapter II. (See the Remote Supervisor Adapter II Installation and User's Guide for more information on using the Remote Supervisor Adapter II web interface.) 3.1.2 Click on Security in the navigation panel. 3.1.3 You are notified that SSL is not installed if the key file has not been loaded previously. Download the key file to a location on your computer, and then specify the location of the file as prompted on the Security page of the web interface. 4.0 Unattended Mode ________________________ Once the files are extracteed from filename.exe, the flash update can be completed by running WFLASH -r at the command prompt. 5.0 WEB Sites and Support Phone Number _________________________________________ 5.1 IBM Support Web Site: http://www.pc.ibm.com/support 5.2 IBM eserver xSeries Web Site: http://www.ibm.com/eserver/xseries 5.3 If you have any questions about this update, or problems applying the update, go to the following Help Center World Telephone Numbers and URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 6.0. TradeMarks and Notices ______________________________ 6.1 The following terms are trademarks of the IBM Corporation in the United States, or other countries or both: * IBM * Netfinity * Netfinity Manager * Advanced System Management Other company, product, and service names may be trademarks or service marks of others. 7.0. Disclaimer __________________ 7.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 7.2 Note to Government users: Note to U.S. Government users-- Documentation related to restricted rights-- Use, duplication and disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation. Appendix A: Package Specific Installation Instruction This update is packaged as a self-extracting PackageForTheWeb (PFTW) executable file. To use this update your TEMP environment variable must be set to a path with read/write access. You must be logged in as an administrator. The command-line syntax for PackageForTheWeb executable device driver update package is: Package.exe [-s] [-a [-s] | [-x directory] | [-?] ] [-s] This command installs an update silently and does not notify you if your files need to be over written in the %temp% directory. [-a] This command passes all subsequent commands to the install package. [-s] This second -s command installs the update silently and unattended. [-x directory] This command extracts the update files to a directory named directory. The PackageForTheWeb executable extracts itself to subdirectory in the %TEMP% directory. Extracted directories will be relative to that location. Typically you must specify an absolute directory. [-?] This command displays information about the command line switches. The command line swithces -a and -x are unattended. Other command line options such as display help (-?) might require that you to hit any key to continue. If Windows packages are run without any command line options, a GUI is displayed. This GUI offers all of the options that are available using the command line.