INSTALL(8) NetBSD System Manager's Manual INSTALL(8) NAME INSTALL - Installation procedure for NetBSD/sun3 DESCRIPTION About this Document This document describes the installation procedure for NetBSD 1.4.2 on the sun3 platform. It is available in four different formats titled INSTALL.ext, where ext is one of .ps, .html, .more, or .txt. .ps PostScript. .html Standard internet HTML. .more The enhanced text format used on Unix-like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line man pages are generally pre- sented. .txt Plain old ASCII. You are reading the ASCII version. What is NetBSD? The NetBSD Operating System is a fully functional Open Source UN*X-like operating system derived from the Berkeley Networking Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on twenty different system architectures featuring eight distinct families of CPUs, and is being ported to more. The NetBSD 1.4.2 release contains complete binary releases for fifteen different machine types. (The remaining ones are not fully supported at this time and are thus not part of the binary distri- bution. For information on them, please see the NetBSD web site at http://www.netbsd.org/) NetBSD is a completely integrated system. In addition to its highly portable, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, The X Window System, and nu- merous other tools, all accompanied by full source code. NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist. Upgrade path to NetBSD 1.4.2 If you are not installing your system ``from scratch'' but instead are going to upgrade an existing system already running NetBSD you need to know which versions you can upgrade with NetBSD 1.4.2. NetBSD 1.4.2 is an upgrade of NetBSD 1.4.1, NetBSD 1.4 and earlier re- leases of NetBSD such as versions 1.3.3, 1.2 etc. The intermediate development versions of code available on the main trunk in our CVS repository (also known as ``NetBSD-current'') from after the point where the release cycle for 1.4 was started are designated by ver- sion identifiers such as 1.4A, 1.4B, 1.4P etc. These identifiers do not designate releases, but indicate major changes in internal kernel APIs. Note that the kernel from NetBSD 1.4.2 can not be used to upgrade a sys- tem running one of those intermediate development versions. Trying to use the NetBSD 1.4.2 kernel on such a system will in all probability re- sult in problems. Please also note that it is not possible to do a direct ``version'' com- parison between any of the intermediate development versions mentioned above and 1.4.2 to determine if a given feature is present or absent in 1.4.2. The development of 1.4, 1.4.1 and 1.4.2 is done on a separate branch in the CVS repository which was created when the release cylcle for 1.4 was started, and during the release cycles for all these versions selective fixes (with minor impact on the stability of the code on the release branch) have been imported from the main development trunk. So, there are features in 1.4.2 which were not in e.g. 1.4H, but the reverse is also true. Major Changes Between 1.4.1 and 1.4.2 The complete list of changes between NetBSD 1.4.1 and 1.4.2 can be found in the file CHANGES-1.4.2 in the top directory of the source tree. The following are the highlights only. o A driver for the Alteon Gigabit Ethernet cards has been added, see ti(4). o A driver for the Realtek 8129/8239 Fast Ethernet PCI cards have been added, see rl(4). o A driver for the DPT SmartCache and SmartRAID III or IV SCSI adapters has been added, see dpt(4). o A driver for the BOCA IOAT66 6-port ISA serial adapter has been added, see ioat(4). o Support for the X-surf Amiga board has been added. o Support has been added for ext2fs revision 1, with read-only support for the ``sparse super'' and the ``filetype'' options. o BIND has been upgraded to version 8.2.2-P5. o The IPF packet filtering software has been updated to version 3.3.5. o Tcpdump now does hex/ascii dumps of packet contents if asked to do so. o An implementation of the System V user management utilities has been added. o The name ``errno'' is now always a macro which expands to a function call. This is done to ease the integration of thread libraries with the code in both system and third-party libraries. Please include to access the correct definition of ``errno''. o A utility for making temporary files for shell scripts has been added, see mktemp(1). o The automounter utility amd(8) has been updated to fix a security problem. o A security problem in procfs has been fixed. Procfs is not used by default in NetBSD. o The floating point emulation on the ports using the m68k CPU has been reverted to the version in NetBSD 1.4 (the version in 1.4.1 had prob- lems). o Several subsystems have received substantial work, such as RAIDframe, LFS, and the package tools. In addition, many, many bugs have been fixed -- more than 100 problems reported through our problem tracking system have been fixed, and many other non-reported problems have also been found and fixed. See the CHANGES-1.4.2 file for the complete list. Known caveats with 1.4.2 The following are the major known issues with NetBSD 1.4.2. o The upgrade of ipf(8) caused a change of the kernel API. Thus, if you are using ipf(8) you need to upgrade both the kernel and the us- er-land utilities to control that feature in order for it to work. o As part of fixing a kernel bug, ``struct vfsnode'' needed to change size. This will unfortunately, and contrary to tradition for patch releases, cause incompatibilities for users of file system LKMs com- piled for 1.4 and 1.4.1. o Although LFS has been improved between 1.4.1 and 1.4.2, it can proba- bly still be characterized as being of ``beta test'' quality, e.g. filling the file system still gives ``interesting'' effects. It should probably not be used to store critical data quite yet. o The version of the IPF packet filtering software in NetBSD 1.4.2 must be enabled with ``ipf -E'' before filtering or NAT rules can be set. Failure to do so may result in a panic. Major Changes Between 1.4 and 1.4.1 The complete list of changes between NetBSD 1.4 and 1.4.1 can be found in the file CHANGES-1.4.1 in the top directory of the source tree. o The NetBSD/alpha port's compatibility for Digital UNIX executables has been greatly improved. o Many bug fixes and improvements of the installation tools and utili- ties. o Support for more PCI serial/parallel cards has been added. o It is now possible to boot NetBSD/i386 on systems with 1GB of RAM. o The floating point emulation on the ports using the m68k CPU has been upgraded. o A fatal problem with /dev/random has been found and fixed. o Support for Alpha 21264 ev6 based systems has been added to NetB- SD/alpha. Major Changes Between 1.3 and 1.4 The NetBSD 1.4 release is a substantial improvement over its predeces- sors. We have provided numerous significant functional enhancements, in- cluding support for many new devices, integration of hundreds of bug fix- es, new and updated kernel subsystems, and many userland enhancements. The results of these improvements is a stable operating system fit for production use that rivals most commercially available systems. It is impossible to completely summarize the nearly two years of develop- ment that went into the NetBSD 1.4 release. Some highlights include: o Substantial improvements in the TCP/IP implementation, including nu- merous performance enhancements and bug fixes by Jason Thorpe and others. o A new, high efficiency kernel memory pool allocator by Paul Kranen- burg. This has been integrated into most kernel subsystems. o A new, totally rewritten virtual memory subsystem, UVM, created by Chuck Cranor, which is substantially cleaner and better performing than the old Mach derived VM subsystem. o Improved POSIX and XPG standards compliance. o Completion of the integration of all remaining 4.4BSD Lite-2 kernel improvements and bug fixes that had not been previously integrated. (Integration of all userland components was completed before NetBSD 1.3) o Several new ports, including macppc, bebox, sparc64, next68k, and others, have been integrated into the source tree. o The system compilers have been upgraded to egcs 1.1.1, and the system compiler toolchain now (mostly) uses the latest versions of GNU binu- tils instead of the obsolete versions left over from 4.4BSD Lite. o Everyone's favorite ftp(1) client has been improved even further. See the man page for details. o A new architecture independent console driver, wscons(4), has been integrated into many ports. o Numerous improvements have been made to the audio subsystem support, including support for MIDI device drivers. o Linux compatibility support has been improved. o A number of scheduler enhancements have yielded dramatic improvements in interactive performance and better control of background tasks. o Several network tunneling protocols, including GRE and IP in IP, have been implemented. o Kernel support for the CODA distributed file system has been added. o Manuel Bouyer completed major changes to the IDE support. It is now architecture independent. Major changes have been made to the IDE code for better error handling, improved ATAPI support, 32 bit data I/O support and bus-master DMA support on PCI IDE controllers. o Lennart Augustsson has added full USB support, permitting the use of a wide variety of Universal Serial Bus peripherals. The drivers should easily port to any future platforms that support the PCI bus. See usb(4) for an overview. o RAIDframe, version 1.1, from the Parallel Data Laboratory at Carnegie Mellon University, has been integrated. Supports RAID levels 0, 1, 4, 5, and more. o Luke Mewburn added nsswitch.conf(5) functionality to the system to specify the search order for system databases. o syslogd(8) now supports listening on multiple sockets, to make the chrooting of servers easier. o Most third party packages have been updated to the latest stable re- lease. As has been noted, there have also been innumerable bug fixes. Kernel interfaces have continued to be refined, and more subsystems and device drivers are shared among the different ports. You can look for this trend to continue. For the sun3, NetBSD 1.4.2 brings combined Sun3 and Sun3X support with the same installation media. The Future of NetBSD The NetBSD Foundation has been incorporated as a non-profit organization. Its purpose is to encourage, foster and promote the free exchange of com- puter software, namely the NetBSD Operating System. The foundation will allow for many things to be handled more smoothly than could be done with our previous informal organization. In particular, it provides the framework to deal with other parties that wish to become involved in the NetBSD Project. The NetBSD Foundation will help improve the quality of NetBSD by: o providing better organization to keep track of development efforts, including co-ordination with groups working in related fields. o providing a framework to receive donations of goods and services and to own the resources necessary to run the NetBSD Project. o providing a better position from which to undertake promotional ac- tivities. o periodically organizing workshops for developers and other interested people to discuss ongoing work. We intend to begin narrowing the time delay between releases. Our ambi- tion is to provide a full release every six to eight months. We hope to support even more hardware in the future, and we have a rather large number of other ideas about what can be done to improve NetBSD. We intend to continue our current practice of making the NetBSD-current development source available on a daily basis. In addition, Anonymous CVS access to the NetBSD source tree has been added since NetBSD 1.4.1; see http://www.netbsd.org/Changes/#anoncvs-available We have also added a browsable CVS repository on the web at http://cvsweb.netbsd.org/cgi-bin/cvsweb.cgi/ We intend to integrate free, positive changes from whatever sources sub- mit them, providing that they are well thought-out and increase the us- ability of the system. Above all, we hope to create a stable and accessible system, and to be responsive to the needs and desires of NetBSD users, because it is for and because of them that NetBSD exists. Sources of NetBSD Please refer to http://www.netbsd.org/Sites/net.html. NetBSD 1.4.2 Release Contents The root directory of the NetBSD 1.4.2 release is organized as follows: .../NetBSD-1.4.2/ BUGS Known bugs list (somewhat incomplete and out of date). CHANGES Changes since earlier NetBSD releases. LAST_MINUTE Last minute changes. MIRRORS A list of sites that mirror the NetBSD 1.4.2 distribution. README.files README describing the distribution's contents. TODO NetBSD's todo list (also somewhat incomplete and out of date). patches/ Post-release source code patches. source/ Source distribution sets; see below. In addition to the files and directories listed above, there is one di- rectory per architecture, for each of the architectures for which NetBSD 1.4.2 has a binary distribution. There are also 'README.export- control' files sprinkled liberally throughout the distribution tree, which point out that there are some portions of the distribution (i.e. the `domestic' portion) that may be subject to export regulations of the United States. It is your responsibility to determine whether or not it is legal for you to export these portions and to act accordingly. The NetBSD project maintains a web page at http://www.NetBSD.ORG/Misc/crypto-export.html which should contain up-to-date information on this issue. The source distribution sets can be found in subdirectories of the "source" subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows: secrsrc.tgz: This set contains the "domestic" sources. These sources may be subject to United States export regulations. 421K gzipped, 2M uncompressed gnusrc.tgz: This set contains the "gnu" sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets. 19M gzipped, 84.3M uncompressed syssrc.tgz: This set contains the sources to the NetBSD 1.4.2 ker- nel, config(8), and dbsym(8). 13.9M gzipped, 68.3M uncompressed sharesrc.tgz: This set contains the "share" sources, which include the sources for the man pages not associated with any par- ticular program, the sources for the typesettable docu- ment set, the dictionaries, and more. 3M gzipped, 11.9M uncompressed src.tgz: This set contains all of the NetBSD 1.4.2 sources which are not mentioned above. 14.4M gzipped, 67.4M uncompressed Most of the above source sets are located in the source/sets subdirectory of the distribution tree. The secrsrc.tgz set is contained in the source/security subdirectory. This set, which may only be available to users in the United States and Canada, contains the sources normally found in /usr/src/domestic - primarily Kerberos and other cryptographic security related software. (Remember, because of United States law, it may not be legal to distribute this set to locations outside of the Unit- ed States and Canada. Again, see http://www.NetBSD.ORG/Misc/crypto-export.html for updated information on this issue.) The source sets are distributed as compressed tar files. They may be un- packed into /usr/src with the command: cat set_name.tgz | gunzip | (cd /; tar xpf - ) The sets/Split/ and security/Split/ subdirectories contain split versions of the source sets for those users who need to load the source sets from floppy or otherwise need a split distribution. The split sets are are named "set_name.xx" where "set_name" is the distribution set name, and "xx" is the sequence number of the file, starting with "aa" for the first file in the distribution set, then "ab" for the next, and so on. All of these files except the last one of each set should be exactly 240,640 bytes long. (The last file is just long enough to contain the remainder of the data for that distribution set.) The split distributions may be reassembled and extracted with cat as follows: cat set_name.?? | gunzip | (cd /; tar xpf - ) In each of the source distribution set directories, there is a file named CKSUMS which contains the checksums of the files in that directory, as generated by the cksum(1) utility. You can use cksum to check the in- tegrity of the archives, if you suspect that one of the files is corrupt and have access to a cksum binary. Checksums based on other algorithms may also be present - see the release(7) man page for details. NetBSD/sun3 Subdirectory Structure The sun3-specific portion of the NetBSD 1.4.2 release is found in the sun3 subdirectory of the distribution: .../NetBSD-1.4.2/sun3/ INSTALL.html INSTALL.ps INSTALL.txt INSTALL.more Installation notes; this file. The .more file contains underlined text using the more(1) conventions for indicat- ing italic and bold display. binary/ sets/ sun3 binary distribution sets; see below. security/ sun3 security distribution; see below. installation/ miniroot/ Sun3 miniroot boot-image. netboot/ Server boot-file image for diskless machines. tapeboot/ Scripts and boot block for making a boot tape. Binary Distribution Sets The NetBSD sun3 binary distribution sets contain the binaries which com- prise the NetBSD 1.4.2 release for the sun3. There are eight binary dis- tribution sets and the security distribution set. The binary distribu- tion sets can be found in the sun3/binary/sets subdirectory of the NetBSD 1.4.2 distribution tree, and are as follows: base The NetBSD 1.4.2 sun3 base binary distribution. You must in- stall this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be minimally functional. It includes shared library support, and excludes everything described below. comp Things needed for compiling programs. This set includes the system include files (/usr/include) and the various system libraries (except the shared libraries, which are included as part of the base set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. etc This distribution set contains the system configuration files that reside in /etc and in several other places. This set must be installed if you are installing the system from scratch, but should not be used if you are upgrading. (If you are upgrading, it's recommended that you get a copy of this set and carefully upgrade your configuration files by hand.) games This set includes the games and their manual pages. man This set includes all of the manual pages for the binaries and other software contained in the base set. Note that it does not include any of the manual pages that are included in the other sets. misc This set includes the (rather large) system dictionaries, the typesettable document set, and other files from /usr/share. text This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages. The sun3 security distribution set is named secr and can be found in the sun3/binary/security subdirectory of the NetBSD 1.4.2 distribution tree. It contains security- related binaries which depend on cryptographic source code. You do not need this distribution set to use encrypted passwords in your password file; the base distribution includes a crypt library which can perform only the one-way encryption function. The security distribution includes a version of the Kerberos IV network security system, and a Kerberized version of telnet(1) program. The secr distribution set can be found only on those sites which carry the complete NetBSD distribution and which can legally obtain it. Because of United States law, it may not be legal to distribute this set to locations outside of the United States and Canada. See http://www.NetBSD.ORG/Misc/crypto-export.html for updated information on this issue. NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on XFree86, and tightly track XFree86 releases. They are currently equivalent to XFree86 3.3.6. Binary sets for the X Window system are distributed with NetBSD. The sets are: xbase The basic files needed for a complete X client environment. This does not include the X servers. xcomp The extra libraries and include files needed to compile X source code. xcontrib Programs that were contributed to X. xfont Fonts needed by X. The sun3 binary distribution sets are distributed as gzipped tar files named with the extension .tgz, e.g. base.tgz. The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the files are /-relative and therefore are extracted below the current directory. That is, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the tar xfp command from /. There is a collection of Sun3 and Sun3X kernels in the sun3/binary/kernels subdirectory of the NetBSD 1.4.2 distribution. The ones named netbsd-ramdisk*.gz contain a root file system image and should only be used for the initial installation. The others are included for convenience. (Most people will want to use netbsd-generic.gz or netbsd- generic3x.gz as appropriate.) Please note that these kernels are simply gzipped and are not in tar archives. Note Each directory in the sun3 binary distribution also has its own checksum files, just as the source distribution does: All BSDSUM files are historic BSD checksums for the various files in that directory, in the format produced by the command: cksum -o 1 file All CKSUM files are POSIX checksums for the various files in that directory, in the format produced by the command: cksum file. All MD5 files are MD5 digests for the various files in that direc- tory, in the format produced by the command: cksum -m file. All SYSVSUM files are historic AT&T System V UNIX checksums for the various files in that directory, in the format produced by the command: cksum -o -2 file. The MD5 digest is the safest checksum, followed by the POSIX checksum. The other two checksums are provided only to ensure that the widest possible range of system can check the integrity of the release files. NetBSD/sun3 System Requirements and Supported Devices NetBSD/sun3 1.4.2 runs on most Sun3 machines, including: 3/50 3/60 3/110 3/75 3/150 3/160 3/260 3/280 3/E 3/80 3/470 Note that NetBSD/sun3 now includes support for "Sun3X" machines, which used to be supported with a separate distribution. The minimal configuration requires 4M of RAM and about 80MB of disk space. To install the entire system requires much more disk space (ap- prox. 100MB additional space is necessary for full sources). To run X or compile the system, more RAM is recommended. Good performance requires 8MB of RAM, or 16 MB when running the X Window System. Here is a table of recommended HD partition sizes for a full install: Partition Advised With X Needed With X root (/) 20M 20M 15M 15M user (/usr) 95M 125M 75M 105M swap ram*2 ... local (/usr/local) up to you ... As you may note, the recommended size of /usr is 20M greater than needed. This is to leave room for a kernel source and compile tree as you will probably want to compile your own kernel. (GENERIC is large and bulky to accommodate all people). Note that the sun3 installation procedure uses a `miniroot' image which is placed into the swap area of the disk. The swap partition must be at least as large as the miniroot image (10MB). The following Sun3 hardware is supported: Serial ports (RS232): built-in ttya, ttyb Video adapters: bwtwo, cgtwo, cgfour Network interfaces: On-board Lance Ethernet On-board or VME Intel Ethernet Sun3/E SCSI/Ethernet board SCSI: (Most SCSI disks, tapes, CD-ROMs, etc.) On-board "esp" (Sun3/80 SCSI) On-board "si" (SCSI-3) VME "si" (SCSI-3) board Sun3/E SCSI/Ethernet board SMD Disks: (the big, heavy ones 8^) Xylogics 450/451 Xylogics 753/7053 Input devices: Sun keyboard and mouse Miscellaneous: Battery-backed real-time clock. On-board floppy controller (Sun3/80 floppy) If it's not on this list, there is no support for it in this release. Getting the NetBSD System on to Useful Media Installation is supported from several media types, including: o Tape o NFS o CD-ROM o FTP Note Installing on a "bare" machine requires some bootable device; ei- ther a tape drive or Sun-compatible NFS server. The procedure for transferring the distribution sets onto installation media depends on the type of media. Instructions for each type of media are given below. In order to create installation media, you will need all the files in the directory .../NetBSD-1.4.2/sun3/ Creating boot/install tapes Installing from tape is the simplest method of all. This method uses two tapes; one called the boot tape, and another called the install tape. The boot tape is created as follows: cd .../NetBSD-1.4.2/sun3/installation/tapeimage sh MakeBootTape /dev/nrst0 The install tape is created as follows: cd .../NetBSD-1.4.2/sun3/installation/tapeimage sh MakeInstallTape /dev/nrst0 If the tapes do not work as expected, you may need to explicitly set the EOF mark at the end of each tape segment. It may also be necessary to use the conv=osync argument to dd(1). Note that this argument is incompati- ble with the bs= argument. Consult the tape-related manual pages on the system where the tapes are created for more details. Boot/Install from NFS server: If your machine has a disk and network connection, but no tape drive, it may be convenient for you to install NetBSD over the network. This in- volves temporarily booting your machine over NFS, just long enough so you can initialize its disk. This method requires that you have access to an NFS server on your network so you can configure it to support diskless boot for your machine. Configuring the NFS server is normally a task for a system administrator, and is not trivial. If you are using a NetBSD system as the boot-server, have a look at the diskless(8) manual page for guidelines on how to proceed with this. If the server runs another operating system, consult the documentation that came with it (i.e. add_client(8) on SunOS). When instructed to boot over the network, your sun3 expects to be able to download a second stage bootstrap program via TFTP after it has acquired its IP address through RARP. It will attempt to download a file using a name derived from the machine's recently aquired IP address. (It may be handy to have a hexadecimal calculator for this next step.) The filename is created by converting the machine's assigned IP address into hexadeci- mal, most-significant octet first, using uppercase characters for the non-decimal (A-F) digits. For example, a sun3 which has been assigned IP address 130.115.144.11 will make an TFTP request for 8273900B. Normally, this file is a symbol- ic link to the NetBSD/sun3 netboot program, which should be located in a place where the TFTP daemon can find it. (Remember, many TFTP daemons run in a chroot'ed environment.) The netboot program may be found in the in- stall directory of this distribution. The netboot program will query a bootparamd server to find the NFS server address and path name for its root, and then load a kernel from that lo- cation. The server should have a copy of the netbsd-rd kernel in the root area for your client (no other files are needed in the client root) and /etc/bootparams on the server should have an entry for your client and its root directory. The client will need access to the miniroot image, which can be provided using NFS or remote shell. If you will be installing NetBSD on several clients, it may be useful to know that you can use a single NFS root for all the clients as long as they only use the netbsd-rd kernel. There will be no conflict between clients because the RAM-disk kernel will not use the NFS root. No swap file is needed; the RAM-disk kernel does not use that either. Install/Upgrade from CD-ROM This method requires that you boot from another device (i.e. tape or net- work, as described above). You may need to make a boot tape on another machine using the files provided on the CD-ROM. Once you have booted netbsd-rd (the RAM-disk kernel) and loaded the miniroot, you can load any of the distribution sets directly from the CD-ROM. The "install" program in the miniroot automates the work required to mount the CD-ROM and ex- tract the files. Install/Upgrade via FTP This method requires that you boot from another device (i.e. tape or net- work, as described above). You may need to make a boot tape on another machine using the files in .../install (which you get via FTP). Once you have booted netbsd-rd (the RAM-disk kernel) and loaded the miniroot, you can load any of the distribution sets over the net using FTP. The "in- stall" program in the miniroot automates the work required to configure the network interface and transfer the files. The preparations for this installation/upgrade method are easy; all you make sure that there's some FTP site from which you can retrieve the NetBSD distribution when you're about to install or upgrade. You need to know the numeric IP address of that site, and, if it's not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. Preparing your System for NetBSD Installation Sun3 machines usually need little or no preparation before installing NetBSD, other than the usual, well advised precaution of backing up all data on any attached storage devices. You will need to know the SCSI target ID of the drive on which you will install NetBSD. Note SunOS/sun3 uses confusing names for the SCSI devices: target 1 is sd2, target 2 is sd4, etc. It might be a good time to run the diagnostics on your Sun3. First, at- tach a terminal to the "ttya" serial port, then set the "Diag/Norm" switch to the Diagnostic position, and power-on the machine. The Diag. switch setting forces console interaction to occur on ttya. Note that the 3/80 has a "software" diag switch you can set at the PROM monitor prompt. To turn on diag boot mode, do: q 70b 12 To return to normal boot mode, do: q 70b 6. The console location (ttya, ttyb, or keyboard/display) is controlled by address 0x1F in the EEPROM, which you can examine and change in the PROM monitor by entering "q1f" followed by a numeric value (or just a '.' if you don't want to change it). Console values are: 00: default graphics display 10: tty a (9600-N-8-1) 11: tty b (1200-N-8-1) 20: Color option board on P4 Installing the NetBSD System Installing NetBSD is a relatively complex process, but if you have this document in hand it should not be too difficult. There are several ways to install NetBSD onto your disk. If your machine has a tape drive the easiest way is "Installing from tape" (details be- low). If your machine is on a network with a suitable NFS server, then "Installing from NFS" is the next best method. Otherwise, if you have another Sun machine running SunOS you can initialize the disk on that ma- chine and then move the disk. (Installing from SunOS is not recommend- ed.) Installing from tape Create the NetBSD/sun3 _VER boot tape as described in the section enti- tled "Preparing a boot tape" and boot the tape. At the PROM monitor prompt, use one of the commands: >b st() >b st(0,8,0) The first example will use the tape on SCSI target 4, where the second will use SCSI target 5. The '>' is the monitor prompt. After the tape loads, you should see many lines of configuration mes- sages, and then the following "welcome" screen: Welcome to the NetBSD/sun3 RAMDISK root! This environment is designed to do only three things: 1: Partititon your disk (use the command: edlabel /dev/rsd0c) 2: Copy a miniroot image into the swap partition (/dev/rsd0b) 3: Reboot (using the swap partition, i.e. /dev/sd?b). Copying the miniroot can be done several ways, allowing the source of the miniroot image to be on any of these: boot tape, NFS server, TFTP server, rsh server The easiest is loading from tape, which is done as follows: mt -f /dev/nrst0 rewind mt -f /dev/nrst0 fsf 2 dd bs=32k if=/dev/nrst0 of=/dev/rsd0b (For help with other methods, please see the install notes.) To reboot using the swap partition, first use "halt", then at the PROM monitor prompt use a command like: b sd(,,1) -s To view this message again, type: cat /.welcome Copy the miniroot as described in the welcome message, and reboot from that just installed miniroot. See the section entitled Booting the miniroot for details. Installing from NFS Before you can install from NFS, you must have already configured your NFS server to support your machine as a diskless client. Instructions for configuring the server are found in the section entitled "Getting the NetBSD System onto Useful Media" above. First, at the Sun PROM monitor prompt, enter a boot command using the network interface as the boot device. On desktop machines this is "le", and "ie" on the others. Examples: >b le() -s >b ie() -s After the boot program loads the RAMDISK kernel, you should see the wel- come screen as shown in the Installing from tape section above. You must configure the network interface before you can use any network resources. For example the command: ssh> ifconfig le0 inet 192.233.20.198 up will bring up the network interface with that address. The next step is to copy the miniroot from your server. This can be done using either NFS or remote shell. (In the examples that follow, the server has IP address 192.233.20.195.) You may then need to add a default route if the server is on a different subnet: ssh> route add default 192.233.20.255 1 You can look at the route table using: ssh> route show Now mount the NFS filesystem containing the miniroot image: ssh> mount -r 192.233.20.195:/server/path /mnt The procedure is simpler if you have space for an expanded (not com- pressed) copy of the miniroot image. In that case: ssh> dd if=/mnt/miniroot of=/dev/rsd0b bs=8k Otherwise, you will need to use "zcat" to expand the miniroot image while copying. This is tricky because the "ssh" program (small shell) does not handle sh(1) pipeline syntax. Instead, you first run the reader in the background with its input set to /dev/pipe and then run the other program in the foreground with its output to /dev/pipe. The result looks like this: ssh> run -bg dd if=/dev/pipe of=/dev/rsd0b obs=8k ssh> run -o /dev/pipe zcat /mnt/install/miniroot.gz To load the miniroot using rsh to the server, you would use a pair of commands similar to the above. Here is another example: ssh> run -b dd if=/dev/pipe of=/dev/rsd0b obs=8k ssh> run -o /dev/pipe rsh 192.233.20.195 zcat miniroot.gz Installing from SunOS To install NetBSD/sun3 onto a machine already running SunOS, you will need the miniroot image (miniroot.gz) and some means to decompress it. First, boot SunOS and place the miniroot file onto the hard drive. If you do not have gzip for SunOS, you will need to decompress the image elsewhere before you can use it. Next, bring SunOS down to single user mode to insure that nothing will be using the swap space on your drive. To be extra safe, reboot the machine into single-user mode rather than using the ``shutdown'' command. Now copy the miniroot image onto your swap device (here /dev/rsd0b) with the command gzip -dc miniroot.gz | dd of=/dev/rsd0b obs=32k or if you have already decompressed the miniroot dd if=miniroot.gz of=/dev/rsd0b obs=32k Finally, reboot the machine and instruct the ROM to boot from the swap device as described in the next section. Booting the Miniroot If the miniroot was installed on partition 'b' of the disk with SCSI tar- get ID=0 then the PROM boot command would be: >b sd(0,0,1) -s With SCSI target ID=2, the the PROM is: >b sd(0,10,1) -s The numbers in parentheses above are: 1. controller (usually zero) 2. unit number (SCSI ID * 8, in hexadecimal) 3. partition number Miniroot Install Program The miniroot's install program is very simple to use. It will guide you through the entire process, and is well automated. Additional improve- ments are planned for future releases. The miniroot's install program will: o Allow you to place disklabels on additional disks. The disk we are installing on should already have been partitioned using the RAMDISK kernel. o Create filesystems on target partitions. o Allow you to set up your system's network configuration. Re- member to specify host names without the domain name appended to the end. For example use `foo' instead of `foo.bar.org'. If, during the process of configuring the network interfaces, you make a mistake, you will be able to re-configure that interface by simply selecting it for configuration again. o Mount target filesystems. You will be given the opportunity to manually edit the resulting /etc/fstab. o Extract binary sets from the media of your choice. o Copy configuration information gathered during the installation process to your root filesystem. o Make device nodes in your root filesystem. o Copy a new kernel onto your root partition. o Install a new boot block. o Check your filesystems for integrity. First-time installation on a system through a method other than the in- stallation program is possible, but strongly discouraged. Post installation steps Once you've got the operating system running, there are a few things you need to do in order to bring the system into a propperly configured state, with the most important ones described below. 1. Configuring /etc/rc.conf If you haven't done any configuration of /etc/rc.conf, the system will drop you into single user mode on first reboot with the message /etc/rc.conf is not configured. Multiuser boot aborted. and with the root filesystem mounted read-write. When the system asks you to choose a shell, simply hit return to get to a prompt. If you are asked for a terminal type, respond with vt220 (or whatever is appropriate for your terminal type) and hit return. At this point, you need to configure at least one file in the /etc directory. Change to the /etc directory and take a look at the /etc/rc.conf file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi-user boot can proceed. If your /usr directory is on a separate partition and you do not know how to use 'ed' or 'ex', you will have to mount your /usr partition to gain access to 'vi'. Do the follow- ing: mount /usr export TERM=vt220 If you have /var on a seperate partition, you need to repeat that step for it. After that, you can edit /etc/rc.conf with vi(1). When you have finished, type exit at the prompt to leave the single-user shell and continue with the multi-user boot. Other values that need to be set in /etc/rc.conf for a networked en- vironment are hostname and possibly defaultroute, furthermore add an ifconfig_int for your interface , along the lines of ifconfig_de0="inet 123.45.67.89 netmask 255.255.255.0" or, if you have myname.my.dom in /etc/hosts: ifconfig_de0="inet myname.my.dom netmask 255.255.255.0" To enable proper hostname resolution, you will also want to add an /etc/resolv.conf file or (if you are feeling a little more adventur- ous) run named(8). See resolv.conf(5) or named(8) for more informa- tion. Other files in /etc that are new to NetBSD 1.4 and may require modi- fication or setting up include /etc/mailer.conf, /etc/nsswitch.conf and /etc/wscons.conf. 2. Logging in After reboot, you can log in as root at the login prompt. There is no initial password, but if you're using the machine in a networked environment, you should create an account for yourself (see below) and protect it and the "root" account with good passwords. 3. Adding accounts Use the vipw(8) command to add accounts to your system, do not edit /etc/passwd directly. See adduser(8) for more information on the process of how to add a new user to the system. 4. The X Window System If you have installed the X window system, look at the files in /usr/X11R6/lib/X11/doc for information. Don't forget to add /usr/X11R6/bin to your path in your shell's dot file so that you have access to the X binaries. 5. Installing 3rd party packages There is a lot of software freely available for Unix-based systems, almost all of which can run on NetBSD. Modifications are usually needed to when transferring programs between different Unix-like systems, so the NetBSD packages collection incorporates any such changes necessary to make that software run on NetBSD, and makes the installation (and deinstallation) of the software packages easy. There's also the option of building a package from source, in case there's no precompiled binary available. Precompiled binaries can be found at ftp://ftp.netbsd.org/pub/NetBSD/packages/ Package sources for compiling packages can be obtained by retrieving the file ftp://ftp.netbsd.org/pub/NetBSD/NetBSD- current/tar_files/pkgsrc.tar.gz and extracting it into /usr/pkgsrc. See /usr/pkgsrc/README then for more information. 6. Misc o To adjust the system to your local timezone, point the /etc/localtime symlink to the appropriate file under /usr/share/zoneinfo. o Edit /etc/aliases to forward root mail to the right place (run newaliases(1) afterwards.) o The /etc/sendmail.cf file will almost definitely need to be ad- justed; files aiding in this can be found in /usr/share/sendmail. See the README file there for more infor- mation. o Edit /etc/rc.local to run any local daemons you use. o Many of the /etc files are documented in section 5 of the manu- al; so just invoking man filename is likely to give you more information on these files. Upgrading a previously-installed NetBSD System It is possible to easily upgrade your existing NetBSD/sun3 system using the upgrade program in the miniroot. If you wish to upgrade your system by this method, simply select the `upgrade' option once the miniroot has booted. The upgrade program with then guide you through the procedure. The upgrade program will: o Enable the network based on your system's current network con- figuration. o Mount your existing filesystems. o Extract binary sets from the media of your choice. o Make new device nodes in your root filesystem. o Copy a new kernel onto your root partition. Note the existing kernel will not be backed up; doing so would be pointless, since older kernels may not be capa- ble of running NetBSD 1.4.2 executables. o Install a new boot block. o Check your filesystems for integrity. Using the miniroot's upgrade program is the preferred method of upgrading your system. However, it is possible to upgrade your system manually. To do this, fol- low the following procedure: o Place at least the `base' binary set in a filesystem accessible to the target machine. A local filesystem is preferred, since the NFS subsystem in the NetBSD 1.4.2 kernel may be incompati- ble with your old binaries. o Back up your pre-existing kernel and copy the 1.4.2 kernel into your root partition. o Reboot with the 1.4.2 kernel into single-user mode. (Otherwise you can not install the boot block.) o Check all filesystems: /sbin/fsck -pf o Mount all local filesystems: /sbin/mount -a -t nonfs o If you keep /usr or /usr/share on an NFS server, you will want to mount those filesystems as well. To do this, you will need to enable the network: sh /etc/netstart o Run the update(8) daemon, to ensure that new programs are actu- ally stored on disk. update o Make sure you are in the root filesystem and extract the `base' binary set: cd / pax -zrvpe -f /path/to/base.tar.gz o Install a new boot block: (assuming root is on /dev/rsd0a) cd /usr/mdec cp -p ./ufsboot /mnt/ufsboot sync ; sleep 1 ; sync ./installboot -v /ufsboot bootxx /dev/rsd0a o Sync the filesystems: sync o At this point you may extract any other binary sets you may have placed on local filesystems, or you may wish to extract additional sets at a later time. To extract these sets, use the following commands: cd / pax -zrvpe -f path to set Note You should not extract the etc set if upgrading. Instead, you should extract that set into another area and carefully merge the changes by hand. Compatibility Issues With Previous NetBSD Releases Users upgrading from previous versions of NetBSD may wish to bear the following problems and compatibility issues in mind when upgrading to NetBSD 1.4.2 Note Only issues effecting an upgrade from NetBSD 1.3 or NetBSD 1.3.x are decribed here. o "machine" directory/link in "/usr/include" Description Some architecture may fail to install the comp set because the /usr/include/machine directory changed to a symbolic link in NetBSD 1.4. Fix If this happens, you can use the command # rm -r /usr/include/machine to remove the old directory and it contents and reinstall the comp set. Using online NetBSD documentation Documentation is available if you first install the manual distribution set. Traditionally, the ``man pages'' (documentation) are denoted by ``name(section)''. Some examples of this are o intro(1), o man(1), o apropros(1), o passwd(1), and o passwd(5). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8. The man command is used to view the documentation on a topic, and is started by entering man [section] topic. The brackets [] around the sec- tion should not be entered, but rather indicate that the section is op- tional. If you don't ask for a particular section, the topic with the lowest numbered section name will be displayed. For instance, after log- ging in, enter man passwd to read the documentation for passwd(1). To view the documentation for passwd(5)m enter man 5 passwd instead. If you are unsure of what man page you are looking for, enter apropos subject-word where subject-word is your topic of interest; a list of possibly related man pages will be displayed. Administrivia If you've got something to say, do so! We'd like your input. There are various mailing lists available via the mailing list server at majordomo@NetBSD.ORG. To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instruc- tions. There are various mailing lists set up to deal with comments and ques- tions about this release. Please send comments to: netbsd- comments@NetBSD.ORG. To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports in- clude lots of details. Additionally, bug reports can be sent by mail to: netbsd-bugs@NetBSD.ORG. Use of send-pr(1) is encouraged, however, because bugs reported with it are entered into the NetBSD bugs database, and thus can't slip through the cracks. There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses. If you're inter- ested in doing a serious amount of work on a specific port, you probably should contact the "owner" of that port (listed below). If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: netbsd-help@NetBSD.ORG. As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP some- where, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. Thanks go to o The former members of UCB's Computer Systems Research Group, includ- ing (but not limited to): Keith Bostic Ralph Campbell Mike Karels Marshall Kirk McKusick for their ongoing work on BSD systems, support, and encouragement. o Also, our thanks go to: Mike Hibler Rick Macklem Jan-Simon Pendry Chris Torek for answering lots of questions, fixing bugs, and doing the various work they've done. o UC Berkeley's Experimental Computing Facility provided a home for sun-lamp in the past, people to look after it, and a sense of humor. Rob Robertson, too, has added his unique sense of humor to things, and for a long time provided the primary FTP site for NetBSD. o Vixie Enterprises for hosting the NetBSD FTP, WWW and SUP server. o Redback Networks, Inc. for hosting the NetBSD Mail server. o Without CVS, this project would be impossible to manage, so our hats go off to Brian Berliner, Jeff Polk, and the various other people who've had a hand in making CVS a useful tool. o Dave Burgess burgess@cynjut.infonet.net has been maintaining the 386BSD/NetBSD/FreeBSD FAQ for quite some time, and deserves to be recognized for it. o The following individuals and organiztions (each in alphabetical or- der) have made donations or loans of hardware and/or money, to sup- port NetBSD development, and deserve credit for it: Steve Allen Jason Birnschein Mason Loring Bliss Jason Brazile Mark Brinicombe David Brownlee Simon Burge Dave Burgess Ralph Campbell Brian Carlstrom James Chacon Bill Coldwell Charles Conn Tom Coulter Charles D. Cranor Christopher G. Demetriou Scott Ellis Hubert Feyrer Castor Fu Greg Gingerich William Gnadt Michael Graff Guenther Grau Ross Harvey Charles M. Hannum Michael L. Hitch Kenneth Alan Hornstein Jordan K. Hubbard Soren Jorvang Scott Kaplan Noah M. Keiserman John Kohl Chris Legrow Ted Lemon Neil J. McRae Perry E. Metzger Herb Peyerl Mike Price Dave Rand Michael Richardson Heiko W. Rupp Brad Salai Chuck Silvers Thor Lancelot Simon Bill Sommerfeld Paul Southworth Ted Spradley Kimmo Suominen Jason R. Thorpe Steve Wadlow Krister Walfridsson Jim Wise Christos Zoulas AboveNet Communications, Inc. Advanced System Products, Inc. Avalon Computer Systems Bay Area Internet Solutions Brains Corporation, Japan Canada Connect Corporation Co-operative Research Centre for Enterprise Distributed Systems Technology Demon Internet, UK Digital Equipment Corporation Easynet, UK Free Hardware Foundation Innovation Development Enterprises of America Internet Software Consortium MS Macro System GmbH, Germany Numerical Aerospace Simulation Facility, NASA Ames Research Center Piermont Information Systems Inc. VMC Harald Frank, Germany Warped Communications, Inc. (If you're not on that list and should be, tell us! We probably were not able to get in touch with you, to verify that you wanted to be listed.) o Finally, we thank all of the people who've put sweat and tears into developing NetBSD since its inception in January, 1993. (Obviously, there are a lot more people who deserve thanks here. If you're one of them, and would like to mentioned, tell us!) We are... (in alphabetical order) The NetBSD core group: Alistair Crooks agc@NetBSD.ORG Jun-ichiro itojun Hagino itojun@NetBSD.ORG Frank van der Linden fvdl@NetBSD.ORG Luke Mewburn lukem@NetBSD.ORG Christos Zoulas christos@NetBSD.ORG The portmasters (and their ports): Mark Brinicombe mark@NetBSD.ORG arm32 Jeremy Cooper jeremy@NetBSD.ORG sun3x Ross Harvey ross@NetBSD.ORG alpha Ignatios Souvatzis is@NetBSD.ORG amiga Jun-ichiro itojun Hagino itojun@NetBSD.ORG sh3 Eduardo Horvath eeh@NetBSD.ORG sparc64 Paul Kranenburg pk@NetBSD.ORG sparc Anders Magnusson ragge@NetBSD.ORG vax Tsubai Masanari tsubai@NetBSD.ORG macppc Tsubai Masanari tsubai@NetBSD.ORG newsmips Minoura Makoto minoura@NetBSD.ORG x68k Phil Nelson phil@NetBSD.ORG pc532 Scott Reynolds scottr@NetBSD.ORG mac68k Darrin Jewell dbj@NetBSD.ORG next68k Kazuki Sakamoto sakamoto@NetBSD.ORG bebox Wolfgang Solfrank ws@NetBSD.ORG ofppc Jonathan Stone jonathan@NetBSD.ORG pmax Shin Takemura takemura@NetBSD.ORG hpcmips Jason Thorpe thorpej@NetBSD.ORG hp300 Frank van der Linden fvdl@NetBSD.ORG i386 Leo Weppelman leo@NetBSD.ORG atari Nathan Williams nathanw@NetBSD.ORG sun3 Steve Woodford scw@NetBSD.ORG mvme68k The NetBSD 1.4.2 Release Engineering team: Chris G. Demetriou cgd@NetBSD.ORG Havard Eidnes he@NetBSD.ORG Ted Lemon mellon@NetBSD.ORG Perry Metzger perry@NetBSD.ORG Curt Sampson cjs@NetBSD.ORG Developers and other contributors: Steve Allen wormey@NetBSD.ORG Julian Assange proff@NetBSD.ORG Lennart Augustsson augustss@NetBSD.ORG Christoph Badura bad@NetBSD.ORG Robert V. Baron rvb@NetBSD.ORG Erik Berls cyber@NetBSD.ORG John Birrell jb@NetBSD.ORG Mason Loring Bliss mason@NetBSD.ORG Manuel Bouyer bouyer@NetBSD.ORG John Brezak brezak@NetBSD.ORG Allen Briggs briggs@NetBSD.ORG Aaron Brown abrown@NetBSD.ORG David Brownlee abs@NetBSD.ORG Frederick Bruckman fredb@NetBSD.ORG Jon Buller jonb@NetBSD.ORG Simon Burge simonb@NetBSD.ORG Dave Burgess burgess@cynjut.infonet.net Robert Byrnes byrnes@NetBSD.org D'Arcy J.M. Cain darcy@NetBSD.ORG Dave Carrel carrel@NetBSD.ORG Bill Coldwell billc@NetBSD.ORG Julian Coleman jdc@NetBSD.ORG Chuck Cranor chuck@NetBSD.ORG Aidan Cully aidan@NetBSD.ORG Johan Danielsson joda@NetBSD.ORG Matt DeBergalis deberg@NetBSD.ORG Rob Deker deker@NetBSD.ORG Chris G. Demetriou cgd@NetBSD.ORG Jaromir Dolecek jdolecek@NetBSD.ORG Andy Doran ad@NetBSD.ORG Roland Dowdeswell elric@NetBSD.ORG Matthias Drochner drochner@NetBSD.ORG Jun Ebihara jun@NetBSD.ORG Havard Eidnes he@NetBSD.ORG Enami Tsugutomo enami@NetBSD.ORG Bernd Ernesti veego@NetBSD.ORG Erik Fair fair@NetBSD.ORG Hubert Feyrer hubertf@NetBSD.ORG Thorsten Frueauf frueauf@NetBSD.ORG Castor Fu castor@NetBSD.ORG Brian R. Gaeke brg@dgate.org Thomas Gerner thomas@NetBSD.ORG Simon J. Gerraty sjg@NetBSD.ORG Justin Gibbs gibbs@NetBSD.ORG Adam Glass glass@NetBSD.ORG Michael Graff explorer@NetBSD.ORG Brian C. Grayson bgrayson@NetBSD.ORG Brad Grantham grantham@tenon.com Matthew Green mrg@NetBSD.ORG Juergen Hannken-Illjes hannken@NetBSD.ORG Charles M. Hannum mycroft@NetBSD.ORG Eric Haszlakiewicz erh@NetBSD.ORG HAYAKAWA Koichi haya@NetBSD.ORG Rene Hexel rh@NetBSD.ORG Michael L. Hitch mhitch@NetBSD.ORG Christian E. Hopps chopps@NetBSD.ORG Ken Hornstein kenh@NetBSD.ORG Marc Horowitz marc@NetBSD.ORG Dean Huxley dean@netbsd.org ITOH Yasufumi itohy@NetBSD.ORG Matthew Jacob mjacob@NetBSD.ORG Lonhyn T. Jasinskyj lonhyn@NetBSD.ORG Chris Jones cjones@NetBSD.ORG Soren Jorvang soren@NetBSD.ORG Antti Kantee pooka@NetBSD.ORG Lawrence Kesteloot kesteloo@cs.unc.edu Thomas Klausner wiz@NetBSD.ORG Klaus Klein kleink@NetBSD.ORG John Kohl jtk@NetBSD.ORG Kevin Lahey kml@NetBSD.ORG Johnny C. Lam jlam@NetBSD.ORG Martin J. Laubach mjl@NetBSD.ORG Ted Lemon mellon@NetBSD.ORG Joel Lindholm joel@NetBSD.ORG Mike Long mikel@NetBSD.ORG Warner Losh imp@NetBSD.ORG Brett Lymn blymn@NetBSD.ORG Paul Mackerras paulus@NetBSD.ORG Dan McMahill dmcmahill@NetBSD.ORG Neil J. McRae neil@NetBSD.ORG Perry Metzger perry@NetBSD.ORG der Mouse mouse@NetBSD.ORG Joseph Myers jsm@NetBSD.ORG Ken Nakata kenn@NetBSD.ORG Bob Nestor rnestor@NetBSD.ORG Tohru Nishimura nisimura@NetBSD.ORG Masaru Oki oki@NetBSD.ORG Greg Oster oster@NetBSD.ORG Herb Peyerl hpeyerl@NetBSD.ORG Matthias Pfaller matthias@NetBSD.ORG Dante Profeta dante@NetBSD.ORG Chris Provenzano proven@NetBSD.ORG Waldi Ravens waldi@moacs.indiv.nl.net Darren Reed darrenr@NetBSD.ORG Michael Richardson mcr@NetBSD.ORG Tim Rightnour garbled@NetBSD.ORG Gordon Ross gwr@NetBSD.ORG Heiko W. Rupp hwr@NetBSD.ORG SAITOH Masanobu msaitoh@NetBSD.ORG Curt Sampson cjs@NetBSD.ORG Wilfredo Sanchez wsanchez@NetBSD.ORG Ty Sarna tsarna@NetBSD.ORG SATO Kazumi sato@NetBSD.ORG Matthias Scheler tron@NetBSD.ORG Karl Schilke (rAT) rat@NetBSD.ORG Konrad Schroder perseant@NetBSD.ORG Tim Shepard shep@NetBSD.ORG Takao Shinohara shin@NetBSD.ORG Chuck Silvers chs@NetBSD.ORG Thor Lancelot Simon tls@NetBSD.ORG Noriyuki Soda soda@NetBSD.ORG Bill Sommerfeld sommerfeld@NetBSD.ORG Bill Studenmund wrstuden@NetBSD.ORG Kevin Sullivan sullivan@NetBSD.ORG Kimmo Suominen kim@NetBSD.ORG Matt Thomas matt@NetBSD.ORG Christoph Toshok toshok@NetBSD.ORG Izumi Tsutsui tsutsui@NetBSD.ORG UCHIYAMA Yasushi uch@NetBSD.ORG Todd Vierling tv@NetBSD.ORG Aymeric Vincent aymeric@NetBSD.ORG Paul Vixie vixie@NetBSD.ORG Krister Walfridsson kristerw@NetBSD.ORG Lex Wennmacher wennmach@NetBSD.ORG Assar Westerlund assar@NetBSD.ORG Rob Windsor windsor@NetBSD.ORG Dan Winship danw@NetBSD.ORG Jim Wise jwise@NetBSD.ORG Colin Wood ender@NetBSD.ORG Legal Mumbo-Jumbo The following notices are required to satisfy the license terms of the software that we have mentioned in this document: This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed by the Computer Systems Engi- neering Group at Lawrence Berkeley Laboratory. This product includes software developed by the NetBSD Foundation, Inc. and its contributors. This product includes software developed by Adam Glass and Charles Han- num. This product includes software developed by Adam Glass. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Charles D. Cranor and Wash- ington University. This product includes software developed by Charles D. Cranor. This product includes software developed by Charles Hannum, by the Uni- versity of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed by Charles Hannum. This product includes software developed by Charles M. Hannum. This product includes software developed by Chris Provenzano. This product includes software developed by Christian E. Hopps. This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Christopher G. Demetriou. This product includes software developed by Christos Zoulas. This product includes software developed by David Jones and Gordon Ross. This product includes software developed by Dean Huxley. This product includes software developed by Eric S. Hvozda. This product includes software developed by Ezra Story. This product includes software developed by Gordon Ross. This product includes software developed by Gordon W. Ross and Leo Wep- pelman. This product includes software developed by Gordon W. Ross. This product includes software developed by Herb Peyerl. This product includes software developed by Ian W. Dall. This product includes software developed by Ignatios Souvatzis for the NetBSD Project. This product includes software developed by Jason R. Thorpe for And Com- munications, http://www.and.com/. This product includes software developed by Joachim Koenig-Baltes. This product includes software developed by Jochen Pohl for The NetBSD Project. This product includes software developed by John Polstra. This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project. This product includes software developed by Jonathan Stone for the NetBSD Project. This product includes software developed by Jonathan Stone. This product includes software developed by Julian Highfield. This product includes software developed by Kenneth Stailey. This product includes software developed by Leo Weppelman. This product includes software developed by Lloyd Parkes. This product includes software developed by Mark Brinicombe. This product includes software developed by Markus Wild. This product includes software developed by Martin Husemann and Wolfgang Solfrank. This product includes software developed by Mats O Jansson and Charles D. Cranor. This product includes software developed by Mats O Jansson. This product includes software developed by Matthias Pfaller. This product includes software developed by Paul Kranenburg. This product includes software developed by Paul Mackerras. This product includes software developed by Peter Galbavy. This product includes software developed by Philip A. Nelson. This product includes software developed by Rodney W. Grimes. This product includes software developed by Scott Bartram. This product includes software developed by SigmaSoft, Th. Lockert. This product includes software developed by Terrence R. Lambert. This product includes software developed by Theo de Raadt and John Brezak. This product includes software developed by Theo de Raadt. This product includes software developed by TooLs GmbH. This product includes software developed by Winning Strategies, Inc. This product includes software developed by the Center for Software Sci- ence at the University of Utah. This product includes software developed by the University of Calgary De- partment of Computer Science and its contributors. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman. This product includes software developed for the FreeBSD project. This product includes software developed for the Internet Software Con- sortium by Ted Lemon. This product includes software developed for the NetBSD Project by Frank van der Linden. This product includes software developed for the NetBSD Project by Jason R. Thorpe. This product includes software developed for the NetBSD Project by John M. Vinopal. This product includes software developed for the NetBSD Project by Matthias Drochner. This product includes software developed for the NetBSD Project by Matthieu Herrb. This product includes software developed for the NetBSD Project by Perry E. Metzger. This product includes software developed for the NetBSD Project by Pier- mont Information Systems Inc. This product includes software developed for the NetBSD Project by Ted Lemon. This product includes software developed by LAN Media Corporation and its contributors. This product includes software developed by Michael Graff for the NetBSD Project. This product includes software developed by Niklas Hallqvist, C Stone and Job de Haas. This product includes software developed by the Computer Systems Labora- tory at the University of Utah. NetBSD 23 March 1999 26